Use this xmodem procedure in order to download a Cisco IOS software image onto a Cisco 1603 Router.
- Launch a terminal emulator program.
In this example, configure Windows HyperTerminal for 8-N-1 at 9600 bps and connect your PC's serial port to the console port of the router. Once connected, you need to get into the ROMmon prompt (rommon 1>). Typically, if the router's Cisco IOS software image and bootflash image are both corrupt, the router only comes up in ROMmon mode. If the former is not true and you need to get into the ROMmon prompt, you need to change the configuration register (typically 0x2102 as given by show version) to 0x0:
1600#configure term Enter configuration commands, one per line. End with CNTL/Z. 1600(config)#configure 1600(config)#config-register 0x0 1600(config)#^Z 1600# 00:22:06: %SYS-5-CONFIG_I: Configured from console by console 1600#reload System configuration has been modified. Save? [yes/no]: n Proceed with reload? [confirm] 00:22:16: %SYS-5-RELOAD: Reload requested System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1) Copyright (c) 1999 by cisco Systems, Inc. Simm with parity detected, ignoring onboard DRAM C1600 platform with 16384 Kbytes of main memory rommon 1 >
- From the ROMmon prompt, issue the xmodem command. However, before you issue the xmodem command, ensure that you have the new Cisco IOS software image on your PC.
In this example, all Flash memory is erased before downloading using the f option (only on the Cisco 1600 Series ). Perform a CRC-16 checksum using the c option and using a download speed of 115200 bps (only on the Cisco 1600 Series ) by specifying -s115200:
Note: If the console port is attached to a modem, both the console port and the modem must be operating at the same baud rate.rommon 12 >xmodem -cfs115200 c1600-sy-mz.121-16.bin Do not start the sending program yet...
Use console speed 115200 bps for download [confirm] File size Checksum File name 1957444 bytes (0x1dde44) 0xe345 c1600-y-mz.113-9.T
Erasing flash at 0x83f0000 no partition 2 on device: PCMCIA slot 1 Ready to receive file c1600-sy-mz.121-16.bin ... Download will be performed at 115200. make sure your terminal emulator is set to this speed before sending file.
Warning:
All existing files in the partition displayed and files in any other partitions on this device will be lost! Continue ? press 'y' for yes, 'n' for no:y
- Configure the terminal emulator program for a data rate of 115200 bps to match the xmodem speed specified above. This is done by closing the previous terminal session of 9600 bps and opening a new one at 115200 with 8-N-1. The trick here is that the Cisco 1603 only supports a maximum baud rate of 9600 bps. Therefore, when connecting at 115200 bps, you cannot see the router prompt. This is an important point to remember. Once connected to the router at 115200 bps, select Transfer and Send File from the HyperTerminal menu bar.
- Specify the image file name and location and enter xmodem as the protocol.
- Click on Send to start the transfer.
This message is received when the transfer is complete:
Download Complete! Returning console speed to 9600 Please reset your terminal emulator to this speed...
- Per the message above, you need to exit your 115200 bps HyperTerminal session and restart a new one at 9600 bps. Once connected, the router's ROMmon prompt appears. Verify that the download was successful by issuing a dir flash:.
rommon 9 >dir flash: File size Checksum File name 3686656 bytes (0x384100) 0x1a5e c1600-sy-mz.121-16.bin
- Change the config register back to 0x2102 and reset or power cycle the router so that the new Cisco IOS software image gets loaded.
rommon 10 >confreg 0x2102 You must reset or power cycle for new config to take effect. rommon 11 >reset System Bootstrap, Version 12.0(19981130:173850) [rameshs-120t_lava 114], DEVELOPMENT SOFTWARE Copyright (c) 1994-1998 by cisco Systems, Inc. Simm with parity detected, ignoring onboard DRAM C1600 platform with 16384 Kbytes of main memory program load complete, entry point: 0x4020060, size: 0x15568c %SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader. program load complete, entry point: 0x2005000, size: 0x3840e0 Self decompressing the image : ######################################## ################ ........ Cisco Internetwork Operating System Software IOS (tm) 1600 Software (C1600-SY-M), Version 12.1(16), RELEASE SOFTWARE (fc1) Copyright (c) 1986-2002 by cisco Systems, Inc. Compiled Mon 08-Jul-02 17:09 by kellythw Image text-base: 0x02005000, data-base: 0x0275BD48 .......
